Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Driveway & Pavers: The Long Beach Owner’s Guide
If you have a Jerith manufactured driveway gate or fence and a paver surface that’s shifting, cracking, or settling around the posts, we stock the Jerith-compatible hardware and the paver materials to get it right. Driveway paver installation in Long Beach runs $7,000 to $18,000, and most repairs or part replacements around a Jerith gate run $400 to $2,000 installed. The typical call we get sounds like this: the gate scrapes the pavers in the afternoon, the post wobbles when the gate swings, or a section of pavers near the driveway apron has sunk half an inch since winter.
Long Beach’s clay-heavy soil expands and contracts through our wet and dry seasons. That movement is the single biggest reason Jerith driveway gates and the pavers underneath them fail together. The gate stays true; the ground underneath does not. We are an independent service provider, not affiliated with Jerith, but we work on their products in Long Beach regularly and keep the common hardware on hand.
Which Jerith Models This Applies To
Jerith builds aluminum and steel residential and light-commercial driveway gates, plus matching fence sections. The driveway gate product lines you’ll see around Long Beach neighborhoods like Bixby Knolls, Los Altos, and El Dorado Park include their single swing, double swing, and slide gate series, each with a different post and hinge configuration. The paver side of this equation is ours: the driveway apron, the walk gate landing, or the paver strip running under the gate’s swing arc.
Before you order any part, check the sticker riveted to the inside of the gate frame near the hinge side. Jerith tags list the model number and date of manufacture. If the tag is gone, measure the gate leaf width and the outside diameter of the hinge post. The single most common compatibility gotcha we see in Long Beach is a homeowner ordering a hinge set for a 4-inch post when their Jerith gate is hung on a 3 1/2-inch post. That quarter inch means the gate binds at the top of its arc or sags at the latch.
For OEM versus aftermarket: Jerith’s proprietary hinge and latch castings are hard to match exactly with off-brand equivalents, and we tell Long Beach homeowners to stick with OEM for the gate hardware. For the paver work under and around the gate, we use quality domestic pavers that match or exceed the original grade. The paver material doesn’t care what brand of gate sits above it; the hinge geometry does.
Beyond Jerith-specific work, we also keep materials on hand for KraftMaid, Cambria, and Silestone projects, but this page is about your Jerith driveway gate and the pavers it has to swing over.
Styles & brands we work with
Signs Your Jerith Driveway & Pavers Is Failing
- The gate scrapes the pavers after 2 p.m. Long Beach sun heats the steel or aluminum leaf, and a gate with worn hinge bushings drops as it expands. If the scrape only happens on hot afternoons, the hinge bushings are worn and the gate has likely been dragging for a while. We replace the bushings, not the whole gate, in most cases.
- Pavers near the hinge post have sunk or cracked. The post may still be set, but the soil under the pavers has compacted unevenly from gate weight and rain. You need the pavers lifted, the base re-compacted, and the pavers relayed. We do this regularly in Long Beach where the native soil shifts between dry and wet cycles.
- The gate rattles at the latch or the latch won’t fully seat. This usually means the post has leaned a few degrees out of plumb. A leaning post pulls the latch geometry just enough that the gate doesn’t close cleanly. Pavers around the post will show a shadow gap where the base settled. The fix is resetting the post and relaying the surrounding pavers, not just tightening the latch.
- Standing water pools on the paver apron after rain. Long Beach rains may be few, but when they come, a low spot in your paver driveway under the gate holds water. That standing water accelerates base erosion and worsens settling. We regrade and re-pitch the pavers away from the house and the gate line.
- You see a hairline crack running from the driveway apron toward the gate post. This is often thermal expansion stress getting concentrated at the paver edge, but in Long Beach it can also signal base washout beneath. If left alone, the next step is a loose post. We treat this as a full base-inspection job, not a surface patch.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Jerith gate hardware replacement in Long Beach, expect $400 to $2,000 installed depending on whether we’re doing hinge bushings and latch adjustment, full hinge replacement, or a complete post reset. For the paver work beneath and around the gate, full driveway paver installation runs $7,000 to $18,000 for a typical Long Beach driveway, and smaller paver repairs around a gate line run $800 to $3,500 depending on the square footage we lift and relay.
What drives the range: depth of the base excavation, whether we need to haul in new crushed rock and sand, the size of the gate we’re resetting, and whether we can salvage the existing pavers or need to source new ones to match. We write the price down before any work starts, and the number we show you is the number on the invoice when we’re done. The labor warranty on our paver and gate work is covered under the 365-Day Done Right Promise: if it’s not right, we make it right.
DIY or Call Us?
You can safely check a few things yourself: look for the Jerith tag, measure the post diameter, and note whether the scrape happens only in the afternoon heat. What you should not do is attempt to adjust a Jerith gate under tension, loosen or shim a gate post, or lift pavers to “see what’s underneath” without knowing the base condition. Gates under load can shift suddenly, and a pinched finger or a gate off its hinges is a bad afternoon. We also see DIY paver patches fail within a year because the base was never the problem. If the gate needs realigning or pavers need relaying, call us at (562) 512-7086 and we’ll come look at it. The estimate is free, and the written price comes before any work starts.
FAQs
A properly installed Jerith aluminum gate lasts 15 to 25 years in Long Beach’s coastal air. Steel lasts 10 to 20 depending on finish and proximity to salt. Pavers under a driveway gate typically need base attention every 8 to 12 years here, because Long Beach soil moves between wet winters and long dry summers. Call (562) 512-7086 if your pavers are shifting and you want an honest read on whether it’s surface or base.
Yes, in most Long Beach homes we lift the existing pavers, re-compact and re-grade the base, and relay the same pavers. Replacement only comes in when the pavers themselves are cracked through, or the original material is no longer available to match. We will tell you which one you’re looking at and give you a written price for the repair before we start.
A hinge bushing and latch adjustment takes one visit, usually half a day. A full post reset with paver relay around the gate takes one to two days depending on base excavation and curing. We keep the same two-person crew on the job from first day to last so the person who opened your gate is the person who closes it out.
We stock the common Jerith hinge bushings, latch sets, and post hardware on the truck for Long Beach calls. If your gate needs a less common Jerith part, we source it from our supplier network and schedule the install once it’s in hand. You will know the price and the timeline before any work begins.
Written by Graham Stein, Owner, Elmstead Remodeling Long Beach at Elmstead Remodeling Long Beach, serving Long Beach and nearby areas.
