Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Long Beach Owner’s Guide
Jerith fence installation in Long Beach typically runs $3,500 to $9,000 for a full residential project, and that includes the aluminum panels, posts, gate hardware, and labor. We keep Jerith-compatible post kits, gate frames, and latch assemblies on the truck, so a failed post or sagging gate can often be swapped the same day we arrive. Most Long Beach owners discover the problem after a windy stretch off the coast or when a gate stops latching cleanly and the dog figures out how to nudge it open.
Which Jerith Models This Applies To
Jerith manufactures residential aluminum fencing in three main series lines that show up regularly in Long Beach backyards: the Regal series, which has a flat-top picket profile and is common in Belmont Shore and Naples; the Estate series, identified by its pressed-spear picket tops and heavier 2-inch posts; and the Patriot series, which you’ll see more often in Bixby Knolls and California Heights with its narrower picket spacing. The residential line all uses 2-inch square posts with a wall thickness that varies by series, and the horizontal rails are a 1-inch profile that slides into routed post openings on both sides.
Here’s the compatibility gotcha that catches people: Jerith’s commercial line uses a completely different post extrusion than the residential line, and the rails will not interchange. If your fence has a 3-inch post, that’s commercial spec, and you need to match it, even if the pickets look identical to a neighbor’s residential fence. The fastest way to identify your series is to measure the post width. If it’s 2 inches, you have the residential line, and the picket cap style tells us which series to pull from stock. We source OEM Jerith panels and posts when the job calls for exact factory match, and we also install quality aftermarket aluminum components that meet the same gauge and powder-coat spec. For black and bronze finishes, the aftermarket options hold up just as well in Long Beach’s salt air, but for anything in Jerith’s newer textured finishes, OEM is the only way to get a true color match.
Styles & brands we work with
Signs Your Jerith Fence Installation Is Failing
- The gate drags across the concrete. The gate post has shifted, usually because the original installer set it in a footing that was too shallow. In Long Beach’s sandy soil near the coast, posts need to sit deeper than the old 18-inch rule that some crews still use.
- Posts lean at the corner or end of a run. Terminal posts carry side load from the tensioned sections, and when the concrete collar cracks, the whole section starts to drift. This is the most common failure we see after a few rainy winters.
- Rust staining runs down from the rail sockets. The factory powder coat has been scratched or chipped at the friction point, exposing the aluminum underneath. Long Beach marine air accelerates this once bare metal is exposed.
- The latch bolt no longer lines up with the strike plate. The gate frame itself has racked, usually because a hinge bearing wore out and the extra play forced the frame to twist. Replacing a hinge early is a $40 fix; waiting turns it into a gate frame replacement.
- Pickets rattle in the bottom rail. The friction fit has failed, often from repeated wind gusts coming off the Los Angeles River channel. Loose pickets stress the rail sockets and eventually crack the post corners.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Jerith fence installation in Long Beach, plan on $3,500 to $9,000 depending on linear footage, gate count, and whether we’re pulling old posts or starting fresh. A single gate post replacement or a gate frame swap lands at the bottom of that range; a whole backyard perimeter with two gates and concrete core-drilling for new post footings lands at the top. The written price we give you before any work starts includes the aluminum panels or post kits, concrete, gate hardware, labor for removal and haul-away of the old section, and a clean-up photo before the crew leaves.
Every Jerith fence installation we do carries the 365-Day Done Right Promise. If a post settles, a gate falls out of alignment, or a latch binds within the first year, we come back and make it right at no charge. And the price Graham Stein writes down on day one is the price on the invoice when we’re done.
DIY or Call Us?
A homeowner can safely handle a few things on a Jerith fence: tightening the latch screws, verifying the gate hinge bolts are snug, and clearing debris from the rail sockets where dirt accumulates. Those are inspection tasks, and they’re worth doing once a season. What goes wrong in DIY land is the post work. Removing a leaning post means digging out a concrete footing, resetting it plumb in wet concrete, and keeping it braced while the mix cures. Get the plumb line off by half an inch and the gate will never latch right again. The panels themselves are not dangerous to handle, but a racked gate under tension can spring when you unbolt the hinge, and aluminum edges are sharp enough to open a hand quickly. If you’re unsure whether the post is the problem or the panel is, call us at (562) 512-7086 and describe what you’re seeing. We’ll tell you honestly whether it’s a job for us or a ten-minute fix you can do with a socket wrench.
FAQs
A properly installed Jerith aluminum fence lasts 30 to 40 years in Long Beach’s coastal climate, with the powder coat holding for most of that span if it isn’t scratched. The weak points are always the gate hinges and latch hardware, which usually need attention every 5 to 8 years. Call (562) 512-7086 if you want us to look at your gate hardware before it takes the post with it.
Yes, in most cases we can cut the post at the base, drill out the old extrusion, and sleeve in a new post section without disturbing the surrounding panels. This only works if the concrete footing is still sound. If the footing is cracked or undersized, we pull the old concrete and pour a new footer. Either way, the written price covers whatever we find, and it doesn’t change after the crew starts.
A gate post replacement or gate frame swap usually takes half a day. A full backyard perimeter with multiple gates and core-drilled footings takes two to three days, and we schedule around children’s nap hours whenever we can. You’ll have the timeline in writing before any work starts.
We stock Jerith-compatible post kits, gate frames, hinge sets, and latch assemblies on the truck, and we can order OEM Jerith panels with exact finish matching. We are an independent service provider and not affiliated with Jerith, but we install their product line regularly in Long Beach. If you need a specific part matched, call (562) 512-7086 and we’ll tell you what we have on the truck that day.
Written by Graham Stein, Owner, Elmstead Remodeling Long Beach at Elmstead Remodeling Long Beach, serving Long Beach and nearby areas.
For your next project, ask us for a free estimate at (562) 512-7086. A live person answers, and the written price comes before any work begins. We also install and stock parts for KraftMaid, Cambria, and Silestone lines on the remodeling side.
